easternvorti.blogg.se - Reolink client change device position

#Reolink client change device position portable#
#Reolink client change device position code#
#Reolink client change device position password#

#Reolink client change device position portable#

The device can be used in portable exposure condition without restriction. The device has been evaluated to meet general RF exposure requirement.

Consult the dealer or an experienced radio/TV technician for help.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Increase the separation between the equipment and receiver.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Part 15 of FCC Rules. Weight: 200g (E1/E1 Pro) Notiﬁcation of Compliance Operating Frequency: 2.4 GHz (E1)/Dual-band (E1 Pro) Operating Temperature: -10☌ to 55☌ (14☏ to 131☏) Size: Φ76 x 106 mm

#Reolink client change device position password#

Set your password using only the characters on the keyboard.ĭisplay Resolution: 4MP (E1 Pro)/3MP (E1) IR Distance: 12 meters (40ft) Pan/Tilt Angle: Horizontal: 355°/Vertical: 50° Power Input: DC 5V/1Aįrame Rate: 15fps (default) Audio: Two-way audio IR Cut Filter: Yes.

Change your WiFi SSID or password and make sure that SSID is within 31 characters and password is within 64 characters.

WPA2-PSK/WPA-PSK (safer encryption) on your router interface.

Change the encryption method of the WiFi network to.

Put your camera close to your router to ensure a strong WiFi signal.

Please ensure you have entered the correct WiFi password.

Please make sure the WiFi band meets the network requirement of the camera.

If the camera fails to connect to WiFi, please try the following solutions:

#Reolink client change device position code#

Try scanning the QR code under a brighter atmosphere.

Vary the distance (about 30cm) between your camera and the mobile phone, which enables the camera to focus better.

Wipe the camera lens with a dry paper/towel/tissue.

Remove the protective ﬁlm from the camera lens.

If the camera failed to scan QR code on your phone, please try the following solutions: If these won’t work, please contact Reolink Support.

Use another 5V power adapter to power up the camera.

If your camera is not powering on, please try the following solutions:

Make sure the power ports are not exposed to water or moisture or blocked by dirt or other elements.

For better image quality, it’s recommended to clean the lens with a soft cloth from time to time.

For better image quality, please make sure that the lighting condition for both the camera and the capture object is the same. Or, it may result in poor image performance.

Do not place the camera in a shaded area and point it towards a well-lit area.

Or, it may result in poor image performance because of the window glare by infrared LEDs, ambient lights or status lights.

Do not point the camera towards a glass window.

Do not face the camera towards any light sources.

Please go to Device Settings -> Display on Reolink app/Client and click Rotation to adjust the image.

In case your camera is mounted upside down, its picture shall be rotated as well.

To remove it from the wall, turn the camera anticlockwise.